Quixant Qxi 200 PC – How to Calibrate & Set up an E Galax Touch Screen

Before attempting, please ensure that you have a USB Keyboard present.

  • Open the top door and insert the USB Keyboard into one of the available USB slots - located on the bottom of the Quixant Qxi 200 PC 
  • Close all the doors
  • Power on the machine
  • Allow the machine to boot up fully into game with all doors shut
  • Press Ctrl Alt and Del on your USB Keyboard
  • This will bring up the Task manager page
  • From the list of files running on the Processes page, arrow down to Typhoon.exe so it is hi lighted blue
  •  Now press Alt and E on your keyboard
  • A Task Manager Warning screen will now pop up, now press Alt and Y on your keyboard to confirm you want to end this process
  • Next, using your arrow up and down keys navigate to Quixant.exe on the Processes list
  • Repeat the same actions, Alt and E on your keyboard
  • Again, a Task Manager Warning screen will now pop up, now press Alt and Y on your keyboard to confirm you want to end this process
  • Now press Alt and F4 on your keyboard, this will close Task Manager down
  • Next press Ctrl and Esc on your keyboard and the following will appear in the bottom left hand corner
    1. All Programs
    2. Log Off
    3. Turn Off computer
  • Press P on your keyboard to select All Programs
  • Arrow down the list until you get to E Galax Touch
  • Now press the arrow right key on your keyboard
  • The following list will appear to the right-hand side of E Galax Touch
    1. Configure Utility
    2. Document
    3. Touch Mon
    4. Uninstall
  • Hi light Configure Utility and press Enter on your keyboard
  • The E Galax Touch – USB Controller page will now appear

Please note that there should be a Blue USB Controller icon inside the white box, if this does not appear please check the USB lead from the PC to the touch screen and also the connection to your Touch screen control board located inside the back monitor plate.  

 

  • Using the Tab key on the keyboard, keep pressing Tab until you get a black dotted line around the General tab
  • Once the black dotted line is around the General tab use the arrow right key to navigate to Tools
  • Now press the Tab key once, this will drop you down to the 4-Point Calibration button
  • Press the Arrow down key on your keyboard, this will take you to Clear and Calibrate, then press Enter on your keyboard
  • The touch screen page will now appear, press, and hold the bottom left target until it says OK then let go
  • Repeat the same process on the remaining 3 other targets
  • Once all 4 targets have been touched a pop-up box will appear saying 4-Point Calibration Completed 
  • Press the OK button 

If you cannot calibrate all 4 of the targets you will need to turn the machine off. Unplug all the connections going to the bottom monitor and take the monitor out of the machine

You will then need to take the touch screen membrane out of its metalwork and thoroughly clean all the membrane including the white edges around the screen.

If you are experiencing a bleeping sound when the screen is pressed please follow the following steps

  • Now the screen is fully calibrated press the Setting tab and the following screen will now appear
    1. Beep on Touch
    2. Beep on Release
    3. Beep from System Beep
    4. Beep from Sound Card
  • Please make sure ALL boxes are UNTICKED 
  • Now press the Apply button
  • Just up from the Apply button there is an Options tab
  • Press the Options tab
  • This will take you into the Options page and show the following 4 options
    1. Enable Constant Touch
    2. Enable Auto Right Click
    3. Enable Touch
    4. Enable Cursor Stabilization
  • Please make sure the top 2 options are UNTICKED (Enable Constant Touch & Enable Auto Right Click) 
  • This will leave the following options ticked (Enable Touch & Enable Cursor Stabilization)
  • Now press Apply then the OK Button
  • This will take you back to the E Galax Touch – USB Controller page
  • Press the Apply button again and then the OK Button
  • This will leave the Storm Splash screen on both screens
  • Now press Ctrl and Esc on your keyboard and the following will appear in the bottom left hand corner
    1. All Programs
    2. Log Off
    3. Turn Off computer
  • Press U on your keyboard to select Turn Off Computer
  • A pop-up screen will now appear with the following
    1. Stand by
    2. Turn Off
    3. Restart
  • Press R on your keyboard to restart your PC
  • The PC will now start to shut down
  • Please remove your USB keyboard